UZMANĪBU! Teksts tulkots ar mašīntulku.
Easy and effortless operation, you can change the direction without noise, and the electric table feed does not vibrate and is not loaded at low speeds, giving you a better operating experience. Small size and easy installation. Excellent speed control over the entire range. The directional function ensures that you can work at any feed speed, which increases efficiency. Directionally dependent knob for quick and easy operation. Also protects drive gears and electronics for long product life. Simply expand your milling machine with an automatic table feed. This is a great way to increase productivity. Note: The carbon brush cover should be opened every 6 months to check if the carbon brushes are worn out. If the carbon brushes are less than 5mm long, they should be replaced immediately (the front and rear carbon brushes should be replaced together). › See more product details; Product description X-Axis Power Feed Table Router Fit Bridgeport Milling Powerfeed Power Feeder 220V Installation instructions: 1. Place the fixed stand on the work table, put the table bearing bushing on the axle screw, then put the table feed on the fixed stand, take out the gear housing. 2. Hold the middle transmission wave with one hand. Place the bevel gear on the axle bolt with the other hand. Then check if the clearance between the gears is between 0.1-0.2 mm. 3. Add locking discs (1.0t, 0.25t, 0.1t) if the game is too big. Repeat step 2-3 until you reach a satisfactory game. 4. Tighten the handle to start adjusting the key and bevel gear. Rotate the handle slightly to feel if there is any interference in between. If so, please repeat step 3-4 and add more washers. If not, go to the next step. 5. Take out the handle, add the correct washer (Φ43xΦ33), adjust the play between dial and bevel gear and secure it with the fixing ring. 6. Adjust the handle and tighten it, turn the handle slightly. Normally, it should be smooth and not disturb. 7. Finally, adjust the gear housing and limit switch. Function Power supply switch and reset switch. 1. The right side of the power switch is \; Product description X-Axis Power Feed Table Router Fit Bridgeport Milling Powerfeed Power Feeder 220V Installation instructions: 1. Place the fixed stand on the work table, put the table bearing bushing on the axle screw, then put the table feed on the fixed stand, take out the gear housing. 2. Hold the middle transmission wave with one hand. Place the bevel gear on the axle bolt with the other hand. Then check if the clearance between the gears is between 0.1-0.2 mm. 3. Add locking discs (1.0t, 0.25t, 0.1t) if the game is too big. Repeat step 2-3 until you reach a satisfactory game. 4. Tighten the handle to start adjusting the key and bevel gear. Rotate the handle slightly to feel if there is any interference in between. If so, please repeat step 3-4 and add more washers. If not, go to the next step. 5. Take out the handle, add the correct washer (Φ43xΦ33), adjust the play between dial and bevel gear and secure it with the fixing ring. 6. Adjust the handle and tighten it, turn the handle slightly. Normally, it should be smooth and not disturb. 7. Finally, adjust the gear housing and limit switch. Function Power supply switch and reset switch. 1. The right side of the power switch is \; X-Axis Power Feed Table Router Fit Bridgeport Milling Powerfeed Power Feeder 220V Installation instructions: 1. Place the fixed stand on the work table, put the table bearing bushing on the axle screw, then put the table feed on the fixed stand, take out the gear housing. 2. Hold the middle transmission wave with one hand. Place the bevel gear on the axle bolt with the other hand. Then check if the clearance between the gears is between 0.1-0.2 mm. 3. Add locking discs (1.0t, 0.25t, 0.1t) if the game is too big. Repeat step 2-3 until you reach a satisfactory game. 4. Tighten the handle to start adjusting the key and bevel gear. Rotate the handle slightly to feel if there is any interference in between. If so, please repeat step 3-4 and add more washers. If not, go to the next step. 5. Take out the handle, add the correct washer (Φ43xΦ33), adjust the play between dial and bevel gear and secure it with the fixing ring. 6. Adjust the handle and tighten it, turn the handle slightly. Normally, it should be smooth and not disturb. 7. Finally, adjust the gear housing and limit switch. Function Power supply switch and reset switch. 1. The right side of the power switch is \